Cuore® PSL 55 D3

Elastic, self-levelling, UV-resistant single-colour polyurethane system; decorative flakes or mother-of-pearl chips are scattered in during installation., des flocons décoratifs ou des paillettes nacrées sont saupoudrés pendant l'application.

Description

Cuore® PSL 55 D3 is an elastic, self-levelling, UV-resistant resin flooring system applied to the floor in one colour, with decorative flakes or mother-of-pearl chips scattered in during installation. 

PSL 55 D3 is part of the Cuore® Design floors range. This system is applied seamlessly and feels soft and warm underfoot. The floor system has a low-maintenance, matt, smooth surface finish. The system has a thickness that can vary between 2 and 3 mm, depending on the substrate and the preparation required.

Areas of application

The Cuore PSL 55 D3 is ideally suited for:

  • Medical sector and healthcare
  • Public buildings; museums, libraries, ...
  • Commercial buildings; shopping centres
  •  Private homes, showrooms, lobbies ...
  • Educational institutions and classrooms 

Environment and health

This Cuore® system may only be installed by experienced professional installers who have completed Cuore training.


System properties

  • Matt finish
  • Seamless
  • Comfortable and soft to the touch
  • Decorative effect: once the floor has been laid, flakes or mother-of-pearl are scattered over it.
  • Low VOC, low emissions
  • Very good mechanical and wear resistance
  • Easy to clean




  1. Primer              : Cuore Ep 1250 / EP 1950
  2. Scraping coat  : Epoxy EP 1250 + GE 100 (1/1 tot 1/1.5)                                    : 1 - 1.5 kg/m²
  3. Resin floor         : Cuore PSL 5450
  4. scatter coat         : decorative flakes/mother-of-pearl 000 or 0000  : 10 - 50 g/m²(consumption to taste)
  5. Top coat           : Cuore WPT 5450 TM
  6. Top coat           : Cuore WPT 5450 TM


        Base                    : Polyurethane

        Colour                    : RAL / NCS colour range

        System thickness  : 2 - 3mm

        VOC content      : 


    Load-bearing capacity : load-bearing, dimensionally stable and sound

    Cleanliness : free from loose particles, dust, oil, grease and rubber marks

    Adhesive tensile strength : min. 1.5 N/mm² (lowest value min. 1.0 N/mm²)

    Compressive strength : min. 25 N/mm²


Consumption

  1. Primer              : Cuore Ep 1250 / EP 1950                                                     : 0.250 - 0.350 kg/m² (per coat)
  2. Scraping coat  : Epoxy EP 1250 + GE 100 (1/1 tot 1/1.5)                                    : 1 - 1.5 kg/m²                      
  3. Resin floor         : Cuore PSL 5450                                                                       : 2.7 kg/m² (at 2 mm thickness)
  4. scatter coat         : decorative flakes/mother-of-pearl 000 or 0000  : 10 - 50 g/m²
  5. Top coat           : Cuore WPT 5450 TM                      : 0.100 - 0.120 kg/m²
  6. Top coat           : Cuore WPT 5450 TM                      : 0.100 - 0.120 kg/m²

All values are theoretical and do not take into account any additional product needed because of the porosity of the substrate, the surface profile or differences in level, nor material losses, etc.

Temperatures

  • Product                              :  +15 °C min. / +30 °C max.
  • Ambient                          :  +15 °C min. / +30 °C max.
  • Surface                      :  +15 °C min. / +30 °C max.
  • Relative humidity : 80 % max
  • Dew point                         : Beware of condensation! The temperature of the substrate and of the uncured product must be at least 3 °C above the dew point in order to reduce the risk of condensation or white bloom on the surface of the applied product.

Moisture content of the substrate 

  • < 4% moisture (parts by weight) Test method: CM method